Mechanics of Materials and Structures Research Group at University of Minnesota
Nanoscale Testing of Collagen Fibrils
Collagen, a molecule consisting of three braided protein helices, is the primary building block of a many biological tissues including bone, tendon, cartilage and skin. Staggered arrays of collagen molecules form fibrils which arrange into higher ordered structures like fibers and fascicles. Because collagen fibrils play a crucial role in determining the response of these tissues to mechanical and chemical forces, significant research has and continues to be directed toward development of theoretical and multi-scale/multi-physics computational models of their stiffness, strength and toughness. Experimental data needed to guide the development of such models, however, is sparse and limited to small strain response. Our research group has taken on the challenge of producing the first experimental monotonic and cyclic stress-strain curves, up to fracture, of single collagen fibrils.
Type I collagen fibrils were isolated from the dermis of sea cucumber, Cucumaria frondosa. The fibrils are several dozen microns long, have cross-sectional dimensions ~10-500 nm, and can be easily isolated from their neighbors. Sea cucumber fibrils are relevant from a biomedical perspective because they are similar to those found in vertebrates. They have the same length, assemble with the same repeat period, and possess the same gap/overlap ratio and cross-linking chemistry. Our ability to measure the mechanical properties of specimens of such dimensions relies on micro-electromechanical systems (MEMS) devices. As described in detail in the references included below, the MEMS platforms have characteristic dimensions in the range of tens to hundreds of micrometers. Pure tension is applied to a collagen fibril (we have also used the same devices to test other one dimensional structures including carbon nanotubes) by attaching one end to a fixed pad, and the other to a pad that moves as a result of actuation by an electrostatic comb drive. The actuator can apply constant, monotonically increasing, or cyclic loading (up to ~10 kHz) depending on whether direct or alternating current voltages are applied. Thus a unique feature of the MEMS platforms is their ability to apply very large numbers of cycles within a relatively short time period and to study the effects of very high frequency mechanical loading on nano scale structures. The elongation of the fibril is measured using a Vernier scale that is fabricated as part of the testing platform
Experimental results were obtained from collagen fibrils immersed in a fluid and others tested in a less humid environment. Very rich mechanical responses were observed, including qualitatively different nominal stress-nominal strain curves (either linear, linear-yielding, or linear-strain softening) and pseudo-elasticity (a hysteretic stress-strain curve with fully recoverable strain). Remarkably, those fibrils tested in a fluid environment achieved strains as high as 150% and ultimate stresses as high as 0.5GPa, depending on specimen size. The results have provided valuable insight that will guide the development of constitutive laws for collagen fibrils.
The MEMS testing platforms developed as part of this research offer promise for probing the mechanical behavior of all kinds of one-dimensional nanoscale structures. The devices can be modified to test two-dimensional specimens under biaxial loading.
1. H. Kahn, R. Ballarini, R.L. Mullen and A.H. Heuer, “Electrostatically Actuated Failure of Microfabricated Polysilicon Fracture Mechanics Specimens,” Proc. R. Soc., A455, 3807-3823, 1999.
2. S. Kamat, X. Su, R. Ballarini and A.H. Heuer, “Structural Basis for the Fracture Toughness of the Shell of the Conch Strombus Gigas, Nature, Vol. 405, June 29, pp. 1036-1040, 2000.
3. H. Kahn, R. Ballarini, J. Bellante and A.H. Heuer, “Fatigue failure in polysilicon not due to simple stress corrosion,” Science, Vol. 298, 1215- 1219, Nov. 8, 2002.
4. S. Eppell, B. Smith, H. Kahn and R. Ballarini, “Nano Measurements With Micro Devices: Mechanical Properties of Hydrated Collagen Fibrils,” Journal of the Royal Society Interface, doi: 10.1098/rsif.2005.0100.
5. Z.L. Shen, M.R. Dodge, H. Kahn, R.Ballarini and S.J. Eppell, “Stress-strain Experiments on Individual Collagen Fibrils,” Biophysical Journal, Vol. 95, 2008, 3956-3963.